PROMOCLEAN™ OVEN 4
PROMOCLEAN™ OVEN 4
20 February 2024

PROMOCLEAN™ OVEN 4 is specially formulated by Inventec for manual cleaning of remelting furnaces and its parts from flux residues.

Due to its formulation and excellent wettability, maintenance time is greatly reduced. Its medium alkaline pH allows effective cleaning without damaging sensitive metals or alloys. It is a ready-to-use product that does not need to be diluted.

 

Features:

  • Removal of all types of hot flux residues
  • Fast and effective cleaning
  • Easy to use
  • Low consumption due to low evaporation rate
  • Greatly reduces equipment downtime
  • Non-toxic and CMR-free
  • Low environmental impact: no GWP, no ODP and low VOC
  • Greenway product
  • Non-flammable/safe replacement of PAHs and other flammable solvents.

 

Application:

PROMOCLEAN™ OVEN 4 is suitable for manual use only. Because it is designed to rapidly release reactive agents, it has a very short bath life when used in cleaning equipment.

The cleaning time depends on the amount of residue and the time between maintenance. Frequent cleaning is recommended for a more efficient cleaning process.

Because the product is nonflammable, it can be used on medium-hot surfaces (maximum 80°C), reducing equipment downtime.

PROMOCLEAN™ DISPER 610 is recommended for cleaning in immersion or spray equipment.

 

Packaging:

  • 750 ml spray
  • 20 kg canister
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
ECOFREC™ TF37I
ECOFREC™ TF37I
20 February 2024

ECOFREC™ TF37I is a tacky flux designed by Inventec for soldering and rework of traditional components and SMDs.

Tacky fluxe ECOFREC™ TF37I allow also metal-free soldering of SMDs on PCBs, the PCBs’solder pads being covered by about 100 microns of metal solid solder deposit (SSD technology such as SIPAD etc…); it also exhibits good printing behavior.

 

Features:

Tacky fluxe ECOFREC™ TF37I is high viscosity fluxe made of complex blending of resins, activators and solvents. After soldering, flux residues remaining on the PCB are non-aggressive and not liable to corrosion. PCB cleaning is thus unnecessary.

 

Application:

This tacky flux can be applied by screen printing, using a stencil or a screen.

Deposits thickness is in the range of 100 microns.

The sticky properties of tacky fluxe ECOFREC™ TF37I ensure that the components will be kept in position until the alloy is reflow using an IR or convection oven or vapour phase. After printing adhesive properties can be improved after 30-60 minutes storage or after heating at 50-60°C during few minutes.

A ready-to-use, prefluxed PCB can be stored several months, away from dust. In order to make storing easier, it is recommended that a non-stick paper be placed between these PCBs.

 

Packaging:

  • 100 g jar
  • 500 g jar
  • 30 g syringe
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
TOPKLEAN™ EL 80
TOPKLEAN™ EL 80
31 January 2024

TOPKLEAN EL 80 is especially designed by Inventec to clean solder flux residues after reflow. It is based on new QSA technology, which allows faster solubilization of organic compounds. A substantial increase of flashpoint, enhanced cleaning performance and reduction of surface tension makes this product the number one choice in it’s application. A guarantee to have perfect cleaning under very low stand-off components. Its excellent ability to solubilize organic and minerals compounds allows to remove almost any solder flux residues used in the electronic industry today. It leaves no white residues and also provides a shiny effect on alloys & metals.

It is used in co-solvent process to offer a fast & sustainable cleaning process with very high cleaning efficiency. In this process, TOPKLEAN™ EL 80 is rinsed perfectly with solvents from our PROMOSOLV™ range. Thanks to the even lower surface tension, the rinsing fluids penetrate into the very tight spaces and under low stand-off components. It will remove any remaining flux residues and cleaning fluids, resulting in very low ionic contamination levels.

Compared with a water-based cleaning system, there is no risk of corrosion due to the absence of residual water left on the boards.

 

Features:

  • Excellent solubility organic & mineral residues
  • Very low surface tension to allow excellent cleaning under low stand-off components
  • Excellent compatibility with materials used on PCB’s
  • Allows shining effect to sensitive alloys & soldered surfaces
  • Non-toxic & no CMR substances
  • No water consumption & no need for wastewater treatment
  • High flash point – safe to use, storage & transport
  • No aromatics & halogenated compounds
  • Low environmental impact: GREENWAY product.

 

Application:

The best process will depend on factors such as operating conditions, equipment, desired cleaning time and the nature of contaminants.

 

Packaging:

  • 20 l canister
  • 200 l drum
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
ECOREL™ 305-16LVD
ECOREL™ 305-16LVD
26 January 2024

ECOREL™ 305-16LVD is especially designed by Inventec to reduce the dimension and amount of voids. This is especially beneficial when soldering bottom terminated components and for applications where excellent thermal management is crucial. A reduction of voids contributes to a better heat dissipation, more reliable electrical connection and a better intermetallic solder joint strength.

The solder paste ECOREL™ 305-16LVD is furthermore well balanced in terms of wettability, reliability, good compatibility with most conformal coating in the market and transparent clear residues. Besides the type 4 solder paste formulations are made from 100% recycled metals and paste in jar packaging can be stored at room temperature, which contributes to an overall reduction in CO2 emissions.

 

Features:

  • Low voiding to offer great heat dissipation
  • Very good wetting on all surface finishes, including OSP
  • Transparent colorless residue, even after multiple reflow cycles
  • Lead Free
  • No halogen
  • Free of CMR containing substances.

 

Application:

The best process will depend on factors such as operating conditions, equipment, board or component design.

Solder paste preparation:

  • Put the paste at room temperature for at least 4 hours prior to use
  • Before printing, it is essential to properly mix the solder paste, either manually with a spatula or by doing several preliminary prints on the stencil
  • Automatic solder paste mixing is neither required nor advised.

 

Packaging:

  • 250g & 500g jar
  • 600g & 1200g cartridge
  • 30g & 100g syringe
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
THERMASOLV™ CF1
THERMASOLV™ CF1
29 December 2023

THERMASOLV™ CF1 is a dielectric fluid formulated by Inventec for heat transfer, dedicated to single-phase direct or immersion cooling systems.

Its high electrical insulation properties allow the fluid to be immersed in live electronic and electrical devices. The product’s favorable viscosity, density and surface tension characteristics allow for optimal surface contact, which contributes to superior heat transfer performance.

Excellent compatibility with all metals, a wide range of plastics and elastomers, and the chemical stability of the fluid make THERMASOLV™ CF1 an ideal fluid for immersion cooling.

THERMASOLV™ CF1 is formulated with safety in mind. It is non-toxic, carries no EUH phrase, is non-flammable, and has no flash point.

 

Features:

  • excellent thermal conductivity
  • very low surface tension
  • high electrical insulation
  • low kinetic viscosity and low freezing point limit the load on pumps.

 

Application:

The best process depends on factors such as operating conditions and equipment. Testing before use is strongly recommended.

The product can be used in the following processes:

  • immersion cooling (single-phase only)
  • direct cooling, in which the fluid flows through cold plates or tubes
  • dielectric testing.

 

Packaging:

  • 8 kg drum
  • 30 kg drum
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
PROMOSOLV™ NEO A2
PROMOSOLV™ NEO A2
22 December 2023

PROMOSOLV™ NEO A2 is especially designed by Inventec to replace rinsing solvents with a high HSE impact and to offer a product in accordance with the latest and future environmental regulations. The very low surface tension allows to penetrate very tight or difficult to access spaces, making sure any cleaning chemistry is fully removed. Besides, the formulation contains a small amount of isopropanol which helps dissolving polar and nonpolar contaminations. For this reason, it is mostly used in electronic defluxing applications.

The newly developed PROMOSOLV NEO range represents products with an Ultra-low to No GWP & low atmospheric lifetime, in order to reduce global warming impact. The solvency power has also been improved, which contributes to an even better & faster cleaning performance.

It can be used in combination with our TOPKLEAN™ range in co-solvent cleaning process to offer an environmentally friendly solvent solution for defluxing or degreasing without compromising on high cleaning performance.

PROMOSOLV™ NEO A2 is compatible with all metals and alloys, including very sensitive ones. It has also good compatibility with most plastics & elastomers, however it is necessary to test before use.

PROMOSOLV™ NEO A2 is formulated with safety in mind, which resulted in a product that is non-flammable and has no flash point.

 

Features:

  • Thermally and chemically stable in use
  • The very low surface tension allows deep cleaning & rinsing of parts with complex geometry
  • Increased solvency power
  • Short cleaning, rinsing and drying times
  • Very low toxicity
  • Ultra-low Global Warming Potential (GWP) & no Ozon depletion potential (ODP)
  • Non-flammable
  • Low environmental impact: GREENWAY product.

 

Application:

The best process will depend on factors such as operating conditions, equipment, desired cleaning time and the nature of contaminants.

 

Packaging:

  • 15 kg canister
  • 30 kg drum
  • 230 kg drum
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
PROMOSOLV™ NEO B1
PROMOSOLV™ NEO B1
21 December 2023

PROMOSOLV™ NEO B1 is developed by Inventec as a drop-in replacement for trichlorethylene, NPB and other solvents with a high Health, Safety & Environmental impact. While reducing substantially the HSE impact, the degreasing power is at an equivalent level. The very low surface tension allows to penetrate very tight or difficult to access spaces, providing a deep cleaning and rinsing.

The newly developed PROMOSOLV™ NEO range represents products with an Ultra-low to No GWP & low atmospheric lifetime, in order to reduce global warming impact. The solvency power has also been improved, which contributes to an even better & faster cleaning performance.

It is dedicated to remove most kind of oils and greases, with the exception of water-based lubricants. Furthermore it is suitable for removing waxes and particles. Depending on the nature of polymerized materials, some varnishes, adhesives, inks & paints could also be removed.

PROMOSOLV™ NEO B1 is compatible with all metals and alloys, including very sensitive ones. It has also good compatibility with most plastics & elastomers, however it is necessary to test before use.

PROMOSOLV™ NEO B1 is formulated with safety in mind, which resulted in a product that has no mentioning of any EUH-phrases. Its composition has excellent flammability suppression properties and is an azeotropic formulation, which provides a very high stability when used in an equipment. Some products in the market may lose their flammability suppression compound due to evaporation when used in an equipment.

 

Features:

  • Thermally and chemically stable in use
  • The very low surface tension allows deep cleaning & rinsing of parts with complex geometry
  • Short cleaning, rinsing and drying times
  • Very low toxicity
  • No Global Warming Potential (GWP) & no Ozon depletion potential (ODP)
  • Non-flammable & azeotropic formulation
  • Low environmental impact: GREENWAY product.

 

Application:
The best process will depend on factors such as operating conditions, equipment, desired cleaning time and the nature of contaminants.

 

Packaging:

  • 35 kg drum
  • 255 kg drum
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
QUICKSOLV™ DEF 90
QUICKSOLV™ DEF 90
19 December 2023

QUICKSOLV™ DEF 90 has been specially developed as a specialty solvent for cold degreasing and drying for an infinite range of materials.

QUICKSOLV™ DEF 90 from Inventec is a non-azeotropic blend of NOVEC™ 3M 7100 and TDE transparent, colorless and a low-odour alternative to ozone-depleting products and developed for cold-cleaning applications.

 

Features:

  • No ozone-depleting potential
  • Chemical and thermal stability
  • Non-flammability and low toxicity.

 

Application:

As with most solvents, QUICKSOLV™ DEF 90 is absorbed by fluorinated plastics and elastomers in the event of prolonged exposure.

 

Packaging:

  • 30 l drum
  • 217 l drum
Last news
Nuova partnership per Chem Solutions
22 February 2024
Chem Solutions è lieta di annunciare una nuova partnership e da oggi è distributore in Italia dei prodotti BROQUETAS.
Chem Solutions diventa distributore di AB Chimie
22 February 2024
Chem Solutions è lieta di annunciare che dal 16 dicembre 2021 è distributore in Italia di ABchimie.
×